Introduction in Automotive ElectronicsModule description #40417 / Version 15
- 6 CP
- Portfolio examination
- Graded
- Winter semester
- German
| Module / Version | #40417 / #15 |
|---|---|
| Validity | Since Summer semester 2026 |
| Available language(s) | English, German |
| Credit points | 6 |
| Person responsible for the module | Gühmann, Clemens |
| Grading | Graded |
| Exam format | Portfolio examination |
| Language(s) of instruction | German |
Affiliation
| Faculty | Fakultät IV |
|---|---|
| Institute | Institut für Energie und Automatisierungstechnik |
| Academic chair | 34311600 FG Elektronische Mess- und Diagnosetechnik |
Contact
| Office | EN 13 |
|---|---|
| Contact person | Heinze, Ewa |
| E-mail address | ewa.heinze@tu-berlin.de |
| Website | http://www.mdt.tu-berlin.de |
Learning outcomes
Significant technological advancements and changes in motor vehicles have been made possible recently by the increase in electrics and electronics, the networking of components and the expansion of functionality through software. After completing the module, students will have knowledge of the most important electronic components (hardware and software) of a vehicle. Furthermore, after completing the module, students can design a measurement chain for digitizing analogue sensor signals, can design a standard automotive controller and develop model-based ECU functions using Simulink/Stateflow.
Content
The lecture “Introduction to Automotive Electronics” first presents the fundamentals of automotive electronics. This includes sensors, actuators, amplifiers, filters, and other electronic and electrical components, bus systems, electronic control units, and the software structures of the control units. The model-based development process is also discussed. Following this, exemplary electronic systems of a vehicle are discussed.
The “Introduction to Automotive Electronics” integrated course covers environmental sensors such as lidar, radar, camera and ultrasound for driver assistance systems. Students first prepare short presentations on the individual sensors. They then simulate driving situations such as obstacle detection using lidar in the laboratory. After developing the algorithms in a simulation, they implement them in a laboratory vehicle. Python programming skills are required for this.
In the integrated course “Automatic Control in Automotive Mechatronics” the focus is on the design of control and regulation of mechatronic systems. The course has a lecture part in which the theory of design is taught. In the subsequent practical phase, a controller is designed based on a model using a concrete, real system (e.g. throttle valve actuator), the implementation is carried out on a microcontroller and then tested.
The “Introduction to Automotive Electronics” integrated course covers environmental sensors such as lidar, radar, camera and ultrasound for driver assistance systems. Students first prepare short presentations on the individual sensors. They then simulate driving situations such as obstacle detection using lidar in the laboratory. After developing the algorithms in a simulation, they implement them in a laboratory vehicle. Python programming skills are required for this.
In the integrated course “Automatic Control in Automotive Mechatronics” the focus is on the design of control and regulation of mechatronic systems. The course has a lecture part in which the theory of design is taught. In the subsequent practical phase, a controller is designed based on a model using a concrete, real system (e.g. throttle valve actuator), the implementation is carried out on a microcontroller and then tested.
Module components
Compulsory area
The following courses are mandatory for this module:
| Courses | Type | Number | Frequency | Language | Hours per week | Course catalog |
|---|---|---|---|---|---|---|
| Einführung in die Automobilelektronik | Lecture | 0430 L 320 | Winter semester | – | 2 | WS 2026/27 (1) ISIS |
Compulsory elective area
A selection of the following courses must be completed:
Courses in the course catalog
Courses created from the teaching units of this module.
Winter semester 2026/27 (1)
Einführung in die Automobilelektronik (Lecture) 1
- Einführung in die Automobilelektronik (Vorlesung) Termingruppe 1 0430 L 320
Workload and credit points
Einführung in die Automobilelektronik (Lecture)
| Workload description | Multiplier | Hours | Total |
|---|---|---|---|
| Attendance | 15 | 2 h | 30 h |
| Pre/post processing and preparation test | 15 | 4 h | 60 h |
| 90 h | |||
Einführung in die Automobilelektronik (Integrated course)
| Workload description | Multiplier | Hours | Total |
|---|---|---|---|
| Attendance | 15 | 2 h | 30 h |
| Pre/post processing | 15 | 4 h | 60 h |
| 90 h | |||
Regelung und Steuerung in der Kraftfahrzeugmechatronik (Integrated course)
| Workload description | Multiplier | Hours | Total |
|---|---|---|---|
| Processing lab tasks including protocol | 4 | 18 h | 72 h |
| Attendance | 9 | 2 h | 18 h |
| 90 h | |||
The workload of the module adds up to 270 hours. The module therefore comprises 6 credit points.
Description of teaching and learning methods
- Lectures (VL): Frontal Lecture
- Integrated course (IV): Frontal lecture and independent processing of lab tasks.
- Integrated course (IV): Frontal lecture and independent processing of lab tasks.
Requirements for participation and examination
Desirable prerequisites for participation in the courses:
Basic knowledge of Electrical Engineering
Basic knowledge of Simulink® / Matlab® and Python
Basic knowledge of Simulink® / Matlab® and Python
Mandatory requirements for the module examination registration:
This module has no examination requirements.
Completion of the module
| Grading | Graded |
|---|---|
| Exam format | Portfolio examination |
| Type of portfolio examination | 100 points in total |
| Language | German |
Test elements
| Name | Points/Weight | Category | Duration/Extent |
|---|---|---|---|
| (Deliverable assessment)Laboratory protocol | 50 | written | 20 Pages |
| (Examination) Test on lecture content | 50 | written | 60 Minutes |
Duration of the module
The following number of semesters is estimated for taking and completing the module: 1 semester(s).
This module can be started in the following semesters: Winter semester.
Maximum number of participants
The maximum capacity of participants is 42.
Registration procedures
Registration for the integrated course is via the corresponding ISIS page. The number of participants is limited to 32 students. If there are too many registrations, the places will be raffled according to the regulations of the TU (AllgStuPO)
Recommended reading, lecture notes
Lecture notes
unavailable
Electronic lecture notes
unavailable – http://www.mdt.tu-berlin.de
Recommended literature
- Borgeest, K: Elektronik in der Fahrzeugtechnik, Hardware, Software, Systeme und Projektmanagement. Springer Vieweg, 2023
- H. Winner, K. C. J. Dietmayer, L. Eckstein, M. Jipp, M. Maurer, und C. Stiller, Hrsg. Handbuch Assistiertes und Automatisiertes Fahren: Grundlagen, Komponenten und Systeme fur ¨ assistiertes und automatisiertes Fahren. Springer-Verlag ATZ/MTZ-Fachbuch. Wiesbaden: Springer Fachmedien Wiesbaden, 4. Auflage, 2024. doi: 10.1007/978-3-658-38486-9.
- M. Botsch, W. Utschick (2020) Fahrzeugsicherheit und automatisiertes Fahren - Methoden der Signalverarbeitung und des maschinellen Lernens Carl Hanser Verlag GmbH & Co. KG
- Bosch: Kraftfahrtechnisches Taschenbuch Wiesbaden, Vieweg Verlag. 2022
- H. Winner, S. Hakuli, F. Lotz, C. Singer (Hrsg); Handbuch Fahrerassistenzsysteme Grundlagen, Komponenten und Systeme für aktive Sicherheit und Komfort. Springer Vieweg, 2015
- Tietze, U.; Schenk, C.; Gamm, E.: Halbleiter-Schaltungstechnik. Springer-Vieweg, 16. Auflage, 2019
- Tschöke, Helmut, et al., editors. Elektrifizierung des Antriebsstrangs: Grundlagen - vom Mikro-Hybrid zum vollelektrischen Antrieb. Springer Berlin Heidelberg, 2019, https://doi.org/10.1007/978-3-662-60356-7.
- Reif, K. (Hrsg.): Sensoren im Kraftfahrzeug. Springer Vieweg. 2017
- Reif, K. (Hrsg.): Busssysteme. Springer Vieweg 2012
- Zimmermann, W.; Schmidgall, R.: Bussysteme in der Fahrzeugtechnik. Springer Vieweg, 2014
- Wallentowitz, H.; Reif, K.:Handbuch der Kraftfahrzeugelektronik. Grundlagen, Komponenten, Systeme und Anwendungen Vieweg ATZ/MTZ-Fachbuch, 2006
- Krüger, M.: Grundlagen der Kfz-Elektronik, Hanser-Verlag, 2020
- P. Scholz: Softwareentwicklung eingebetteter Systeme
- Schäuffele, J.; Zurawka, T. Automotive Software Engineering. Grundlagen, Prozesse, Methoden und Werkzeuge effizient einsetzen. 6. Auflage. Vieweg ATZ/MTZ-Fachbuch. 2016
- J. Wietzke, J.; Tran, M.T: Automotive Embedded Systeme
Assigned programs
This module version is used in the following programs:
| Program / program version | Semester(s) | Curriculum component |
|---|---|---|
| Automotive Engineering (teacher training) Automotive Engineering (teacher training) (B. Sc.) - Kernfach StuPO 2020 | SS 2026 | Wahlpflichtbereich › Fachwissenschaftlicher Wahlpflichtbereich |
| WS 2026/27 | Wahlpflichtbereich › Fachwissenschaftlicher Wahlpflichtbereich | |
| Automotive Engineering (teacher training) Automotive Engineering (teacher training) (B. Sc.) - Zweitfach StuPO 2020 | SS 2026 | Wahlpflichtbereich › Fachwissenschaftlicher Wahlpflichtbereich |
| WS 2026/27 | Wahlpflichtbereich › Fachwissenschaftlicher Wahlpflichtbereich | |
| Automotive Systems Automotive Systems (M. Sc.) - StuPO 2017 | SS 2026 | Pflichtbereich › Kernmodule |
| WS 2026/27 | Pflichtbereich › Kernmodule | |
| Computational Engineering Science (Informationstechnik im Maschinenwesen) StuPO 2018 | SS 2026 | 6. Schwerpunkte › 6.2 Mechatronische Systeme |
| WS 2026/27 | 6. Schwerpunkte › 6.2 Mechatronische Systeme | |
| Industrial Engineering and Management Industrial Engineering and Management (M. Sc.) - StuPO 2015 | SS 2026 | Ingenieurwissenschaftliche Studienrichtungen/Engineering Majors › Elektrotechnik/Electrical Engineering (ET) › Elektrotechnik/Electrical Engineering (Wahlpflicht/Compulsory-Elective) › Electronics & Integrated Systems |
| WS 2026/27 | Ingenieurwissenschaftliche Studienrichtungen/Engineering Majors › Elektrotechnik/Electrical Engineering (ET) › Elektrotechnik/Electrical Engineering (Wahlpflicht/Compulsory-Elective) › Electronics & Integrated Systems | |
| Industrial Engineering and Management Industrial Engineering and Management (M. Sc.) - StuPO 2026 | WS 2026/27 | Engineering Sciences / Specialization › Electrical Engineering › Electronics & Integrated Systems |
| Technomathematics Technomathematics (M. Sc.) - StuPO 2014 | SS 2026 | Studienrichtungen › Verkehrswesen › Verkehrswesen › Fahrzeugtechnik |
| WS 2026/27 | Studienrichtungen › Verkehrswesen › Verkehrswesen › Fahrzeugtechnik | |
| Vehicle Engineering StuPO 2017 | SS 2026 | 1. Kernmodule |
| WS 2026/27 | 1. Kernmodule |
Not specified
Miscellaneous
The IV can only be offered if enough scientific staff is available.