Space ElectronicsModule description #50036 / Version 3
- 6 CP
- Portfolio examination
- Graded
- Winter and summer semester
- English
This module description is not valid in the current semester (Winter semester 2026/27).
Current version (v4)
| Module / Version | #50036 / #3 |
|---|---|
| Validity | Summer semester 2021 – Winter semester 2023/24 |
| Available language(s) | English |
| Credit points | 6 |
| Person responsible for the module | Avsar, Cem |
| Grading | Graded |
| Exam format | Portfolio examination |
| Language(s) of instruction | English |
Affiliation
| Faculty | Fakultät V |
|---|---|
| Institute | Institut für Luft- und Raumfahrt |
| Academic chair | 35341200 FG Raumfahrttechnik |
Contact
| Office | F 6 |
|---|---|
| Contact person | Avsar, Cem |
| E-mail address | cem.avsar@tu-berlin.de |
| Website | http://www.mse.tu-berlin.de |
Learning outcomes
Nowadays, it is required that space systems engineers have basic knowledge and skills in electronics. Electronics and electrical hardware and software are significant parts of any space mission. The systems engineer must understand the main requirements on spacecraft equipment and their interconnections with respect to electrical characteristics and interfaces. The module imparts the practical skills relevant to designing hardware and software for a spacecraft.
After completion of the course, the student will be able to
- recognize the importance of having knowledge in electronics as space systems engineer,
- recognize conventions (e.g. names, symbols, units) that are commonly used in electronics,
- explain the concepts of electrical potential (e.g. voltage, current, work, power, DC, AC),
- recognize the hazards of working with electronics,
- use basic laboratory equipment for electronics (e.g. multimeter, power supply, oscilloscope, frequency generator),
- apply basic laws of electronics for circuit design (e.g. voltage, current, work, power, Ohm’s law, Kirchhoff’s laws),
- use basic analog parts for circuit design (e.g. resistor, capacitor, diodes, transistors, op-amps),
- design basic circuit diagrams for the purpose of interfacing with equipment (e.g. sensors, actuators, computers),
- use breadboards for prototyping electrical circuits,
- simulate the behavior of circuits using software tools,
- design printed circuit boards,
- explain the processes of manufacturing and procuring printed circuit boards,
- solder circuit boards,
- interpret datasheet of integrated circuits,
- connect and use any integrated circuit,
- apply basic laws of digital electronics (binary coding, binary calculations, hexadecimal, gate logic),
- explain the internal composition of microcontrollers,
- use basic functions of a microcontroller (e.g. interrupts, I/Os, timer, ADC, PWM, communication interfaces, memory),
- controls sensors and actuators using a microcontroller (e.g. temperature sensor, IMU, servo),
- explain the challenges of space electronics design,
- explain the approach for the design, realization, and qualification of electronics in the different phases of a space project,
- describe the general electrical architecture of a satellite,
- describe special features of space electronics design (e.g. current limiting, latch-up protection, redundancy),
- select the relevant ECSS standards for electrical design,
- recognize the challenges of spacecraft on-board software design,
- explain the software architecture of a satellite,
- practice the steps of the software development process.
After completion of the course, the student will be able to
- recognize the importance of having knowledge in electronics as space systems engineer,
- recognize conventions (e.g. names, symbols, units) that are commonly used in electronics,
- explain the concepts of electrical potential (e.g. voltage, current, work, power, DC, AC),
- recognize the hazards of working with electronics,
- use basic laboratory equipment for electronics (e.g. multimeter, power supply, oscilloscope, frequency generator),
- apply basic laws of electronics for circuit design (e.g. voltage, current, work, power, Ohm’s law, Kirchhoff’s laws),
- use basic analog parts for circuit design (e.g. resistor, capacitor, diodes, transistors, op-amps),
- design basic circuit diagrams for the purpose of interfacing with equipment (e.g. sensors, actuators, computers),
- use breadboards for prototyping electrical circuits,
- simulate the behavior of circuits using software tools,
- design printed circuit boards,
- explain the processes of manufacturing and procuring printed circuit boards,
- solder circuit boards,
- interpret datasheet of integrated circuits,
- connect and use any integrated circuit,
- apply basic laws of digital electronics (binary coding, binary calculations, hexadecimal, gate logic),
- explain the internal composition of microcontrollers,
- use basic functions of a microcontroller (e.g. interrupts, I/Os, timer, ADC, PWM, communication interfaces, memory),
- controls sensors and actuators using a microcontroller (e.g. temperature sensor, IMU, servo),
- explain the challenges of space electronics design,
- explain the approach for the design, realization, and qualification of electronics in the different phases of a space project,
- describe the general electrical architecture of a satellite,
- describe special features of space electronics design (e.g. current limiting, latch-up protection, redundancy),
- select the relevant ECSS standards for electrical design,
- recognize the challenges of spacecraft on-board software design,
- explain the software architecture of a satellite,
- practice the steps of the software development process.
Content
The module consists of two lecture courses. In Space Electronics 1, the focus is set on introducing the student to analog electronics, handling basic hardware and software tools. Space Electronics 2 sets a focus on digital electronics. The following main topics are covered in the course.
- Basic analog parts (e.g. resistor, capacitor, diode, transistor, op-amp)
- Using basic electrical laws (e.g. Ohm's law, Kirchoffs laws)
- Design and simulation of electrical circuits (e.g. KiCAD, LTSpice)
- Handling of laboratory equipment (e.g. mulitmeter, oscilloscope)
- Basics of digital electronics (e.g. ICs, boolean algebra, microcontrollers)
- Programming of microcontrollers
- Hardware related electronic design aspects for spacecraft
- Software related electronics design aspects for spacecraft
- Basic analog parts (e.g. resistor, capacitor, diode, transistor, op-amp)
- Using basic electrical laws (e.g. Ohm's law, Kirchoffs laws)
- Design and simulation of electrical circuits (e.g. KiCAD, LTSpice)
- Handling of laboratory equipment (e.g. mulitmeter, oscilloscope)
- Basics of digital electronics (e.g. ICs, boolean algebra, microcontrollers)
- Programming of microcontrollers
- Hardware related electronic design aspects for spacecraft
- Software related electronics design aspects for spacecraft
Module components
Compulsory area
The following courses are mandatory for this module:
| Courses | Type | Number | Frequency | Language | Hours per week | Course catalog |
|---|---|---|---|---|---|---|
| Space Electronics 1 | Lecture | Summer semester | [en] | 2 | ISIS | |
| Space Electronics 2 | Lecture | Winter semester | [en] | 2 | WS 2026/27 (1) ISIS |
Courses in the course catalog
Courses created from the teaching units of this module.
Winter semester 2026/27 (1)
Space Electronics 2 (Lecture) 1
- Space Electronics 2 (Vorlesung) 1. Termingruppe
Workload and credit points
Space Electronics 1 (Lecture)
| Workload description | Multiplier | Hours | Total |
|---|---|---|---|
| Attendance | 15 | 2 h | 30 h |
| Homework assignments | 3 | 10 h | 30 h |
| Self-study of lecture materials | 15 | 1 h | 15 h |
| Test preparation | 1 | 15 h | 15 h |
| 90 h | |||
Space Electronics 2 (Lecture)
| Workload description | Multiplier | Hours | Total |
|---|---|---|---|
| Attendance | 15 | 2 h | 30 h |
| Project work | 1 | 30 h | 30 h |
| Self-study of lecture materials | 15 | 1 h | 15 h |
| Test preparation | 1 | 15 h | 15 h |
| 90 h | |||
The workload of the module adds up to 180 hours. The module therefore comprises 6 credit points.
Description of teaching and learning methods
The course is hands-on oriented. Each student receives a package with several electronics parts and measurement equipment. The lectures are mostly interactive, meaning that the students build circuits and program their microcontroller under guidance of the lecturer. The parts are also needed for the regular homework assignments. Each student works on a small individual practical project in which a variety of the newly learned skills are applied.
Requirements for participation and examination
Desirable prerequisites for participation in the courses:
This module has no desirable prerequisites for the courses.
Mandatory requirements for the module examination registration:
This module has no examination requirements.
Completion of the module
| Grading | Graded |
|---|---|
| Exam format | Portfolio examination |
| Type of portfolio examination | 100 points in total |
| Language | English |
Test elements
| Name | Points/Weight | Category | Duration/Extent |
|---|---|---|---|
| Assignments | 30 | flexibel | 30 hours |
| Project work | 30 | practical | 30 hours |
| Test | 40 | written | 1 hour |
Exam description
Space Electronics 1 has graded assignments. The hardware kit is used to complete the assignments which are partially of hands-on nature.
In Space Electronics 2, the students work on a small electronics project either individually or in groups of two. The student demonstrates the project results by the end of the semester.
A 1 hour written test assesses knowledge that is covered in the theoretical lectures of Space Electronics 1 and 2.
In Space Electronics 2, the students work on a small electronics project either individually or in groups of two. The student demonstrates the project results by the end of the semester.
A 1 hour written test assesses knowledge that is covered in the theoretical lectures of Space Electronics 1 and 2.
Duration of the module
The following number of semesters is estimated for taking and completing the module: 2 semester(s).
This module can be started in the following semesters: Winter and summer semester.
Maximum number of participants
This module is not limited to a number of students.
Registration procedures
Registration at the MSE secretary according to the MSE study and examination regulations. Dates and deadlines will be announced by semester start.
Recommended reading, lecture notes
Lecture notes
unavailable
Electronic lecture notes
unavailable
Recommended literature
- Agarwal, A., Lang, J. H., Foundations of Analog and Digital Electronic Circuits, San Francisco, Elsevier, 2005.
- Ley, W., Wittmann, K., Hallmann, W., Handbook of Space Technology., Chichester: John Wiley & Sons, Ltd, 2009.
- Macdonald, M., Badescu, V., The International Handbook of Space Technology., Heidelberg: Springer, 2014.
- Platt, C., MAKE Electronics, O'Reilly, 2009
- Wiley, L. J., Wertz, J. R., Space Mission Analysis and Design., El Segundo: Microcosm Press, 2005.
Assigned programs
This module is not used in any program.
The course is limited to students from the Master of Space Engineering study programme.
Miscellaneous
Not specified