Skip to content
Technische Universität Berlin Deutsch
Course catalog and module transfer system

Introduction in Automotive ElectronicsModule description #40417 / Version 12

← Module page Deutsche Fassung
This module description is not valid in the current semester (Winter semester 2026/27). Current version (v15)
Module / Version#40417 / #12
ValidityWinter semester 2024/25 – Summer semester 2025
Available language(s)German
Credit points6
Person responsible for the moduleGühmann, Clemens
GradingGraded
Exam formatWritten exam
Language(s) of instructionGerman

Affiliation

FacultyFakultät IV
InstituteInstitut für Energie und Automatisierungstechnik
Academic chair34311600 FG Elektronische Mess- und Diagnosetechnik

Contact

OfficeEN 13
Contact personHeinze, Ewa
E-mail addressewa.heinze@tu-berlin.de
Websitehttp://www.mdt.tu-berlin.de

Learning outcomes

Significant technological advancements and changes in motor vehicles have been made possible recently by the increase in electrics and electronics, the networking of components and the expansion of functionality through software. After completing the module, students will have knowledge of the most important electronic components (hardware and software) of a vehicle. Furthermore, after completing the module, students can design a measurement chain for digitizing analogue sensor signals, can design a standard automotive controller and develop model-based ECU functions using Simulink/Stateflow.

Content

The lecture "Introduction to Automotive Electronics" is divided into two sections. In the first section, the basics of automotive electronics are presented. Sensors, actuators, amplifiers, filters and other electronic and electrical components, bus systems, electronic control units and the software structures of the control units are dealt with. The model-based development process is also dealt with. Subsequently, exemplary electronic systems of a vehicle are treated.

The practical course "Lab Introduction in Automotive Electronics" focuses on the application of model-based development of automotive ECUs. In the so-called model-in-the-loop simulation, a function for controlling e.g. a transmission is designed, tested and optimized using MATLAB/Simulink.

In the integrated course "Automatic Control in Automotive Mechatronics" the focus is on the design of control and regulation of mechatronic systems. The course has a lecture part in which the theory of design is taught. In the subsequent practical phase, a controller is designed based on a model using a concrete, real system (e.g. throttle valve actuator), the implementation is carried out on a microcontroller and then tested.

Module components

Compulsory area

The following courses are mandatory for this module:

CoursesTypeNumberFrequencyLanguageHours per weekCourse catalog
Einführung in die AutomobilelektronikLecture0430 L 320 Winter semester–2 ISIS

Compulsory elective area

A selection of the following courses must be completed:

CoursesTypeNumberFrequencyLanguageHours per weekCourse catalog
Einführung in die AutomobilelektronikInternship Winter semester[de]2 ISIS
Regelung und Steuerung in der KraftfahrzeugmechatronikIntegrated course Winter semester[de]2 ISIS

Courses in the course catalog

Courses created from the teaching units of this module.

Winter semester 2026/27 (1)

Einführung in die Automobilelektronik (Lecture) 1

All groups of this course in the catalog

Workload and credit points

Einführung in die Automobilelektronik (Lecture)

Workload descriptionMultiplierHoursTotal
Präsenzzeit152 h30 h
Vor-/Nachbereitung154 h60 h
90 h

Einführung in die Automobilelektronik (Internship)

Workload descriptionMultiplierHoursTotal
Attendance152 h30 h
Pre/post processing154 h60 h
90 h

Regelung und Steuerung in der Kraftfahrzeugmechatronik (Integrated course)

Workload descriptionMultiplierHoursTotal
Bearbeitung der Praktikumsaufgaben418 h72 h
Präsenzzeit92 h18 h
90 h

The workload of the module adds up to 270 hours. The module therefore comprises 6 credit points.

Description of teaching and learning methods

- Lectures (VL): Frontal Lecture
- Lab (PR): independent processing of tasks
- Integrated course (IV): Frontal lecture and independent processing of tasks.

Requirements for participation and examination

Desirable prerequisites for participation in the courses:

Basic knowledge of Simulink® / Matlab®

Mandatory requirements for the module examination registration:

The examination requirements could not be retrieved.

Completion of the module

GradingGraded
Exam formatWritten exam
LanguageGerman
Duration/Extent120 min

Exam description

Insgesamt können 100 Portfoliopunkte erreicht werden:
* Vorlesung (50 Portfoliopunkte)
* Praktikum (insgesamt 50)

Im Rahmen des Praktikums sind verschiedene Studienleistungen zu erbringen. Ihre
Art und Gewichtung in Portfoliopunkten sind in der unten stehenden Tabelle aufgeführt. Die Gesamtnote gemäß §47 (2) AllgStuPO wird nach dem Notenschlüssel 2 der Fakultät IV ermittelt.

Duration of the module

The following number of semesters is estimated for taking and completing the module: 1 semester(s).

This module can be started in the following semesters: Winter semester.

Maximum number of participants

The maximum capacity of participants is 42.

Registration procedures

The chosen elective course (from Wahlpflichtbereich) must be passed to attend the exam "Introduction to Automotive Electronics" (Einführung in die Automobilelektronik).
Registration for the lab is via the corresponding ISIS page.
The number of participants in the lab is limited to 32 students.
If there are too many registrations, the places will be raffled according to the regulations of the TU (OTU).

Recommended reading, lecture notes

Lecture notes

unavailable

Electronic lecture notes

available – http://www.mdt.tu-berlin.de

Recommended literature

  • Borgeest, K: Elektronik in der Fahrzeugtechnik, Hardware, Software, Systeme und Projektmanagement. Springer Vieweg, 2023
  • Bosch: Kraftfahrtechnisches Taschenbuch Wiesbaden, Vieweg Verlag. 2022
  • H. Winner, S. Hakuli, F. Lotz, C. Singer (Hrsg); Handbuch Fahrerassistenzsysteme Grundlagen, Komponenten und Systeme für aktive Sicherheit und Komfort. Springer Vieweg, 2015
  • Tietze, U.; Schenk, C.; Gamm, E.: Halbleiter-Schaltungstechnik. Springer-Vieweg, 16. Auflage, 2019
  • Tschöke, Helmut, et al., editors. Elektrifizierung des Antriebsstrangs: Grundlagen - vom Mikro-Hybrid zum vollelektrischen Antrieb. Springer Berlin Heidelberg, 2019, https://doi.org/10.1007/978-3-662-60356-7.
  • Reif, K. (Hrsg.): Sensoren im Kraftfahrzeug. Springer Vieweg. 2017
  • Reif, K. (Hrsg.): Busssysteme. Springer Vieweg 2012
  • Zimmermann, W.; Schmidgall, R.: Bussysteme in der Fahrzeugtechnik. Springer Vieweg, 2014
  • Wallentowitz, H.; Reif, K.:Handbuch der Kraftfahrzeugelektronik. Grundlagen, Komponenten, Systeme und Anwendungen Vieweg ATZ/MTZ-Fachbuch, 2006
  • Krüger, M.: Grundlagen der Kfz-Elektronik, Hanser-Verlag, 2020
  • P. Scholz: Softwareentwicklung eingebetteter Systeme
  • Schäuffele, J.; Zurawka, T. Automotive Software Engineering. Grundlagen, Prozesse, Methoden und Werkzeuge effizient einsetzen. 6. Auflage. Vieweg ATZ/MTZ-Fachbuch. 2016
  • J. Wietzke, J.; Tran, M.T: Automotive Embedded Systeme

Assigned programs

This module version is used in the following programs:

Program / program versionSemester(s)Curriculum component
Automotive Engineering (teacher training)
Automotive Engineering (teacher training) (B. Sc.) - Kernfach StuPO 2020
SS 2025Wahlpflichtbereich › Fachwissenschaftlicher Wahlpflichtbereich
Automotive Engineering (teacher training)
Automotive Engineering (teacher training) (B. Sc.) - Zweitfach StuPO 2020
SS 2025Wahlpflichtbereich › Fachwissenschaftlicher Wahlpflichtbereich
Automotive Systems
Automotive Systems (M. Sc.) - StuPO 2017
SS 2025Pflichtbereich › Kernmodule
Computational Engineering Science (Informationstechnik im Maschinenwesen)
StuPO 2018
SS 20256. Schwerpunkte › 6.2 Mechatronische Systeme
Industrial Engineering and Management
Industrial Engineering and Management (M. Sc.) - StuPO 2015
WS 2024/25Ingenieurwissenschaftliche Studienrichtungen/Engineering Majors › Elektrotechnik/Electrical Engineering (ET) › Elektrotechnik/Electrical Engineering (Wahlpflicht/Compulsory-Elective) › Electronics & Integrated Systems
SS 2025Ingenieurwissenschaftliche Studienrichtungen/Engineering Majors › Elektrotechnik/Electrical Engineering (ET) › Elektrotechnik/Electrical Engineering (Wahlpflicht/Compulsory-Elective) › Electronics & Integrated Systems
Technomathematics
Technomathematics (M. Sc.) - StuPO 2014
SS 2025Studienrichtungen › Verkehrswesen › Verkehrswesen › Fahrzeugtechnik
Vehicle Engineering
StuPO 2017
SS 20251. Kernmodule
Master Automotive Systems
Master Fahrzeugtechnik
B.Sc. Fahrzeugtechnik (teaching profession)

Miscellaneous

The lab can only be offered if enough scientific staff is available.