Lightweight Design IModule description #50399 / Version 7
- 6 CP
- Portfolio examination
- Graded
- Winter semester
- German
| Module / Version | #50399 / #7 |
|---|---|
| Validity | Since Summer semester 2025 |
| Available language(s) | English, German |
| Credit points | 6 |
| Person responsible for the module | Bardenhagen, Andreas |
| Grading | Graded |
| Exam format | Portfolio examination |
| Language(s) of instruction | German |
Affiliation
| Faculty | Fakultät V |
|---|---|
| Institute | Institut für Luft- und Raumfahrt |
| Academic chair | 35341100 FG Luftfahrzeugbau und Leichtbau |
Contact
| Office | F 2 |
|---|---|
| Contact person | Bardenhagen, Andreas |
| E-mail address | andreas.bardenhagen@tu-berlin.de |
| Website | http://www.tu-berlin.de/?id=58558 |
Learning outcomes
The aim is to acquire knowledge about
- the fundamental phenomena of the load-bearing behavior of structures
- the topological design of lightweight structures using the example of aircraft structures
- the design problems and mechanical characteristics of thin-walled lightweight structures
- the modeling of lightweight structures using the mechanical elements profile bar, beam, shear panel and sheet
- failure modes for thin-walled structures
The aim is to learn skills in
- design and dimensioning of load-bearing structures according to stresses
- Calculation of internal forces in beam-shaped load-bearing structures
- Calculation and analysis of stress states in thin-walled profile bars and the resulting deformation under load
- Application of strength hypotheses for isotropic materials
- Design of skin fields using the shear panel chord model
- Determination of the stress states and deformations of sheet elements
- Application of Airy's stress function for the analysis of stress states, decay behavior of disturbance stresses and the co-supporting width
- Analysis of the excessive stress on cut-outs and application of countermeasures
The aim is to acquire expertise
- for the weight-optimized topological design of lightweight structures,
- investigate and dimension load-bearing structures using suitable analytical methods,
- generate and predict structural responses (e.g. deformations) and
- consider sustainability and ethical aspects in the design of load-bearing structures.
- the fundamental phenomena of the load-bearing behavior of structures
- the topological design of lightweight structures using the example of aircraft structures
- the design problems and mechanical characteristics of thin-walled lightweight structures
- the modeling of lightweight structures using the mechanical elements profile bar, beam, shear panel and sheet
- failure modes for thin-walled structures
The aim is to learn skills in
- design and dimensioning of load-bearing structures according to stresses
- Calculation of internal forces in beam-shaped load-bearing structures
- Calculation and analysis of stress states in thin-walled profile bars and the resulting deformation under load
- Application of strength hypotheses for isotropic materials
- Design of skin fields using the shear panel chord model
- Determination of the stress states and deformations of sheet elements
- Application of Airy's stress function for the analysis of stress states, decay behavior of disturbance stresses and the co-supporting width
- Analysis of the excessive stress on cut-outs and application of countermeasures
The aim is to acquire expertise
- for the weight-optimized topological design of lightweight structures,
- investigate and dimension load-bearing structures using suitable analytical methods,
- generate and predict structural responses (e.g. deformations) and
- consider sustainability and ethical aspects in the design of load-bearing structures.
Content
- Problems of lightweight design: load assumptions, force introduction, joints and cut-outs, strength hypotheses, shear flow in thin-walled structures, torsion and warping
- Lightweight construction materials: Metallic and isotropic materials
- Basic elements of lightweight design: rod, beam and panel
- Open and closed thin-walled profile beams under bending, shear force and torsion
- Isotropy and orthotropy (material and geometric)
- Designing for stresses: Internal forces, calculation of stresses and shear flows, application of strength hypotheses, avoidance of notch effects and stress peaks
- Consideration of the design criteria: Stiffness, strength and stability
- Effects of lightweight construction on the performance of the product and on the environmental footprint
- Principles of scientific work
- Lightweight construction materials: Metallic and isotropic materials
- Basic elements of lightweight design: rod, beam and panel
- Open and closed thin-walled profile beams under bending, shear force and torsion
- Isotropy and orthotropy (material and geometric)
- Designing for stresses: Internal forces, calculation of stresses and shear flows, application of strength hypotheses, avoidance of notch effects and stress peaks
- Consideration of the design criteria: Stiffness, strength and stability
- Effects of lightweight construction on the performance of the product and on the environmental footprint
- Principles of scientific work
Module components
Compulsory area
The following courses are mandatory for this module:
| Courses | Type | Number | Frequency | Language | Hours per week | Course catalog |
|---|---|---|---|---|---|---|
| Leichtbau I | Integrated course | 3534 L 216 | Winter semester | [de] | 6 | WS 2026/27 (1) ISIS |
Courses in the course catalog
Courses created from the teaching units of this module.
Winter semester 2026/27 (1)
Leichtbau I (Integrated course) 1
- Leichtbau I (Integrierte Veranstaltung) 1. Termingruppe 3534 L 216
Workload and credit points
Leichtbau I (Integrated course)
| Workload description | Multiplier | Hours | Total |
|---|---|---|---|
| Homework | 4 | 7.5 h | 30 h |
| Lecture Course | 15 | 4 h | 60 h |
| Preparation and follow-up work | 15 | 6 h | 90 h |
| 180 h | |||
The workload of the module adds up to 180 hours. The module therefore comprises 6 credit points.
Description of teaching and learning methods
Lecture, exercise, demonstration and homework
Requirements for participation and examination
Desirable prerequisites for participation in the courses:
Analysis, linear algebra, differential equations
Mechanics, Materials engineering
Mechanics, Materials engineering
Mandatory requirements for the module examination registration:
This module has no examination requirements.
Completion of the module
| Grading | Graded |
|---|---|
| Exam format | Portfolio examination |
| Type of portfolio examination | 100 points in total |
| Language | German |
Test elements
| Name | Points/Weight | Category | Duration/Extent |
|---|---|---|---|
| writing exam | 50 | written | 50 min |
| oral test | 50 | oral | 15 min |
Exam description
Form of examination: this portfolio examination consists of a written exam and an oral consultation.
Duration of the module
The following number of semesters is estimated for taking and completing the module: 1 semester(s).
This module can be started in the following semesters: Winter semester.
Maximum number of participants
This module is not limited to a number of students.
Registration procedures
Examination must be registered in accordance with the valid examination regulations.
Recommended reading, lecture notes
Lecture notes
unavailable
Electronic lecture notes
unavailable
Recommended literature
- Linke/Nast: Festigkeitslehre für den Leichtbau. Springer 2015
- Wiedemann: Leichtbau Elemente und Konstruktion. 3. Aufl. Springer 2007
- Megson: Aircraft Structures for Engineering Students. 5th ed. Elsevier 2013
Assigned programs
This module version is used in the following programs:
| Program / program version | Semester(s) | Curriculum component |
|---|---|---|
| Aeronautics and Astronautics StuPO 2018 | WS 2025/26 | 2. Kernmodule › 2.2 Luftfahrzeugbau und Leichtbau |
| SS 2026 | 2. Kernmodule › 2.2 Luftfahrzeugbau und Leichtbau | |
| WS 2026/27 | 3. Profilmodule › 3.2 Luftfahrzeugbau und Leichtbau | |
| Engineering Science StuPO 09.01.2012 | WS 2025/26 | 04. Grundlagen Wahlpflicht › Wahlpflichtmodule |
| SS 2026 | 04. Grundlagen Wahlpflicht › Wahlpflichtmodule | |
| Engineering Science StuPO 2020 | WS 2025/26 | Wahlpflichtmodule › 4. Grundlagen Wahlpflicht › 4.5 Allgemeine Grundlagen |
| SS 2026 | Wahlpflichtmodule › 4. Grundlagen Wahlpflicht › 4.5 Allgemeine Grundlagen | |
| WS 2026/27 | Wahlpflichtmodule › 4. Grundlagen Wahlpflicht › 4.5 Allgemeine Grundlagen | |
| Industrial Engineering and Management Industrial Engineering and Management (B. Sc.) - StuPO 2015 | WS 2025/26 | Ingenieurwissenschaftliche Studienrichtungen › Verkehrswesen (VW) › Verkehrswesen (Wahlpflicht) |
| SS 2026 | Ingenieurwissenschaftliche Studienrichtungen › Maschinenbau (MB) › Maschinenbau (Wahlpflicht) | |
| WS 2026/27 | Ingenieurwissenschaftliche Studienrichtungen › Verkehrswesen (VW) › Verkehrswesen (Wahlpflicht) | |
| Industrial Engineering and Management Industrial Engineering and Management (M. Sc.) - StuPO 2015 | WS 2025/26 | Ingenieurwissenschaftliche Studienrichtungen/Engineering Majors › Verkehrswesen/Transportation Engineering (VW) › Verkehrswesen/Transportation Engineering (Wahlpflicht/Compulsory-Elective) › Aerospace Engineering |
| SS 2026 | Ingenieurwissenschaftliche Studienrichtungen/Engineering Majors › Verkehrswesen/Transportation Engineering (VW) › Verkehrswesen/Transportation Engineering (Wahlpflicht/Compulsory-Elective) › Aerospace Engineering | |
| WS 2026/27 | Ingenieurwissenschaftliche Studienrichtungen/Engineering Majors › Verkehrswesen/Transportation Engineering (VW) › Verkehrswesen/Transportation Engineering (Wahlpflicht/Compulsory-Elective) › Aerospace Engineering | |
| Industrial Engineering and Management Industrial Engineering and Management (M. Sc.) - StuPO 2026 | WS 2026/27 | Engineering Sciences / Specialization › Transportation Engineering › Aerospace Engineering |
| Mechanical Engineering StuPO 2017 | WS 2025/26 | Wahlpflichtmodule › Kernmodule › Berechnung |
| SS 2026 | Wahlpflichtmodule › Kernmodule › Berechnung | |
| WS 2026/27 | Wahlpflichtmodule › Kernmodule › Berechnung | |
| Mechanical Engineering StuPO 2017 | WS 2025/26 | Wahlpflichtmodule › Schwerpunktmodule › Methodenorientierung › Mechanik |
| SS 2026 | Wahlpflichtmodule › Schwerpunktmodule › Methodenorientierung › Mechanik | |
| WS 2026/27 | Wahlpflichtmodule › Schwerpunktmodule › Methodenorientierung › Mechanik | |
| Naval Architecture and Ocean Engineering StuPo 2017 | WS 2025/26 | 2. Profilmodule › 2.3 Strukturanalyse |
| SS 2026 | 2. Profilmodule › 2.3 Strukturanalyse | |
| WS 2026/27 | 2. Profilmodule › 2.3 Strukturanalyse | |
| Technomathematics Technomathematics (M. Sc.) - StuPO 2014 | WS 2025/26 | Studienrichtungen › Verkehrswesen › Verkehrswesen › Luft- und Raumfahrttechnik |
| SS 2026 | Studienrichtungen › Verkehrswesen › Verkehrswesen › Luft- und Raumfahrttechnik | |
| WS 2026/27 | Studienrichtungen › Verkehrswesen › Verkehrswesen › Luft- und Raumfahrttechnik | |
| Transport Systems StuPO 2018 | WS 2025/26 | B. Studienrichtungen › Luft- und Raumfahrttechnik › 4. Vertiefungs- und Anwendungsbereich |
| SS 2026 | A. Grundlagen › 2. Wahlpflichtbereich › 2.2 Technisch-naturwissenschaftliche Grundlagen | |
| WS 2026/27 | B. Studienrichtungen › Luft- und Raumfahrttechnik › 4. Vertiefungs- und Anwendungsbereich |
Suitable degree programs:
• Transportation Engineering, Aerospace Engineering, Mechanical Engineering, Physical Engineering
Science
• Other engineering programs with a focus on structural mechanics
Foundation for:
• Lightweight Design II
• Composite Lightweight Design I and II
• Transportation Engineering, Aerospace Engineering, Mechanical Engineering, Physical Engineering
Science
• Other engineering programs with a focus on structural mechanics
Foundation for:
• Lightweight Design II
• Composite Lightweight Design I and II
Miscellaneous
Not specified